Thermomechanical Analysis of Isora Nanofibril Incorporated Polyethylene Nanocomposites.

The research on cellulose fiber-reinforced nanocomposites has increased by an unprecedented magnitude over the past few years due to its wide application range and low production cost. However, the incompatibility between cellulose and most thermoplastics has raised significant challenges in composite fabrication. This paper addresses the behavior of plasma-modified polyethylene (PE) reinforced with cellulose nanofibers extracted from isora plants (i.e., isora nanofibrils (INFs)). The crystallization kinetics of PE-INF composites were explained using the Avrami model. The effect of cellulose nanofillers on tuning the physiochemical properties of the nanocomposite was also explored in this work. The increase in mechanical properties was due to the uniform dispersion of fillers in the PE. The investigation on viscoelastic properties confirmed good filler-matrix interactions, facilitating the stress transfer.

Gas Barrier, Rheological and Mechanical Properties of Immiscible Natural Rubber/Acrylonitrile Butadiene Rubber/Organoclay (NR/NBR/Organoclay) Blend Nanocomposites.

In this paper, gas permeability studies were performed on materials based on natural rubber/acrylonitrile butadiene rubber blends and nanoclay incorporated blend systems. The properties of natural rubber (NR)/nitrile rubber (NBR)/nanoclay nanocomposites, with a particular focus on gas permeability, are presented. The measurements of the barrier properties were assessed using two different gases-O2 and CO2-by taking in account the blend composition, the filler loading and the nature of the gas molecules. The obtained data showed that the permeability of gas transport was strongly affected by: (i) the blend composition-it was observed that the increase in acrylonitrile butadiene rubber component considerably decreased the permeability; (ii) the nature of the gas-the permeation of CO2 was higher than O2; (iii) the nanoclay loading-it was found that the permeability decreased with the incorporation of nanoclay. The localization of nanoclay in the blend system also played a major role in determining the gas permeability. The permeability of the systems was correlated with blend morphology and dispersion of the nanoclay platelets in the polymer blend.

A new device for real-time peroperative monitoring of ossicular chain reconstruction during middle ear surgery.

To limit functional surgical failure and reduce the rate of revision surgery in case of surgical ossicular chain reconstruction, a piezoelectric device was developed for assessment of ossicular chain vibrations during the middle ear surgery. The device resembled a pen and consisted of a reusable main body and a disposable sensitive head including piezoelectric polymer sensor. Almost all of components of the device were made of polymer for light weight and for acoustic impedance matching to the middle ear system. Several frequencies can be analyzed simultaneously and several measures can be taken by time. The results showed that the device can record normal and reconstructed ossicular chain vibration in response to an acoustic stimulation, with similar results to those achieved by laser Doppler vibrometer. This light, handheld and low-cost device allows fast, easy and safe assessments of normal ossicular chain mobility and ossicular chain reconstruction efficiency. Primary pre-clinical trial showed very promising performance of the device that could be used to qualitatively control ossiculoplasty during real-time surgical procedure. Clinical assessments will be done to further evaluate the real-life performance of the device.

Flexible and self-standing nickel ferrite-PVDF-TrFE cast films: promising candidates for high-end magnetoelectric applications.

Polymer-based magnetoelectrics are identified as a newly emerging area of research due to their profound potential applications centered on spintronic technology. In line with this, we have developed a novel, flexible nickel ferrite (NiFe2O4)-PVDF-TrFE (NF-PVDF-TrFE) polymer based magnetoelectric film, with excellent magnetoelectric coupling at room temperature. Nanocomposite films were prepared by the solution cast method, in which the nickel ferrite nanoparticles with different weight percentages (2, 4, 8 and 16%) were incorporated in the electroactive PVDF-TrFE polymer matrix. The ferroelectric ß-crystalline phase of PVDF-TrFE was confirmed by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR) and Raman studies. Dielectric and thermal properties of the composite films were found to be substantially improved with the addition of magnetic nanoparticles. Ferroelectric and magnetic characteristics of the composite films were also considerably improved with an increase in NiFe2O4 concentration. A magnetic saturation (Ms) of 4.81 emu g-1 and a ferroelectric maximum polarization of 18.9 µC cm-2 were shown by the composite film at room temperature for 16 wt% loading of NF nanoparticles. Besides these functionalities, ac and dc magnetoelectric coupling coefficients of 69 mV cm-1 Oe-1 and 90 mV cm-1 Oe-1 were obtained for 16NF-PVDF-TrFE along with excellent mechanical stability. These flexible and self-standing magnetoelectric composite films with enhanced magnetoelectric coupling coefficients at room temperature could be suitable candidates for the development of ultramodern information storage devices, memory devices, signal processing devices etc.

Development of titanium dioxide nanowire incorporated poly(vinylidene fluoride-trifluoroethylene) scaffolds for bone tissue engineering applications.

Critical size bone defects that do not heal spontaneously are among the major reasons for the disability in majority of people with locomotor disabilities. Tissue engineering has become a promising approach for repairing such large tissue injuries including critical size bone defects. Three-dimension (3D) porous scaffolds based on piezoelectric polymers like poly(vinylidene fluoride-trifluoroethylene) (P(VDF-TrFE)) have received a lot of attention in bone tissue engineering due to their favorable osteogenic properties. Owing to the favourable redox properties, titanium dioxide (TiO2) nanostructures have gained a great deal of attention in bone tissue engineering. In this paper, tissue engineering scaffolds based on P(VDF-TrFE) loaded with TiO2 nanowires (TNW) were developed and evaluated for bone tissue engineering. Wet-chemical method was used for the synthesis of TNW. Obtained TNW were thoroughly characterized for the physicochemical and morphological properties using techniques such as X-Ray diffraction (XRD) analysis and transmission electron microscopy (TEM). Electrospinning was used to produce TNW incorporated P(VDF-TrFE) scaffolds. Developed scaffolds were characterized by state of art techniques such as Scanning Electron Microscopy (SEM), XRD and Differential scanning calorimetry (DSC) analyses. TEM analysis revealed that the obtained TiO2 nanostructures possess nanofibrous morphology with an average diameter of 26 ± 4 nm. Results of characterization of nanocomposite scaffolds confirmed the effective loading of TNW in P(VDF-TrFE) matrix. Fabricated P(VDF-TrFE)/TNW scaffolds possessed good mechanical strength and cytocompatibility. Osteoblast like cells showed higher adhesion and proliferation on the nanocomposite scaffolds. This investigation revealed that the developed P(VDF-TrFE) scaffolds containing TNW can be used as potential scaffolds for bone tissue engineering applications.

Thermal, biodegradation and theoretical perspectives on nanoscale confinement in starch/cellulose nanocomposite modified via green crosslinker.

In this research work, we propose a synergistic effect of a green crosslinker and cellulose nanomaterial on the crystallinity, viscoelastic, and thermal properties of starch nanocomposites. A disaccharide derivative was used as a bio crosslinker and nanofiber from pineapple leaf as a reinforcing phase for starch. Sucrose was oxidised using periodate, that can selectively oxidise the vicinal hydroxyl group of sucrose and form tetra aldehyde derivative. Crystallinity of films after crosslinking decreased with successive addition of crosslinker. The melting temperature of films increased because of formation of more dense structure after crosslinking. Morphological investigations were analysed by atomic force microscopy. Polymer chain confinement and mechanics were quantified. The crosslink densities of the films were calculated using two models, phantom model and affine model, using storage modulus data. By using very low amount of crosslinker and nanoreinforcement, the properties of thermoplastic starch were significantly improved.

Magnetic performance and defect characterization studies of core-shell architectured MgFe2O4@BaTiO3 multiferroic nanostructures.

Multiferroics that permit manipulation of the magnetization vector exclusively by electric fields have spawned extensive interest for memory and logic device applications. In line with this understanding, we herein report the encapsulation of non-ferroelectric magnesium ferrite (MgFe2O4) nanoparticles in a ferroelectric shell of BaTiO3 to produce a system with engineered dielectric, magnetic, magneto-electric and ferroelectric properties. The interface effect on the strain transfer was observed to strongly influence the magneto-electric coupling and the electric and magnetic properties of the system. The model polyhedral image of MgFe2O4@BaTiO3 has helped to get an insight into the core-shell structure. The multiferroicity induced by the excellent coupling between the ferroelectric and magnetostrictive phases at the core-shell interface unlocks wide prospects for device downscaling and information storage applications. The influence of magnetostrictive stress on the magneto-electric coupling effects and domain dynamics was further studied using transmission electron microscopy (TEM) and atomic force microscopy images. Interestingly, the realization of a superparamagnetic multiferroic system has been a breakthrough and facilitates ultra high density magnetic data storage technologies. Evidence for spontaneous polarization and the ferroelectric trait exhibited by the multiferroic samples was revealed from the P-E hysteresis loop. The investigation of defect evolution in the system was carried out using positron annihilation lifetime spectroscopy (PALS) and coincidence Doppler broadening spectroscopy (CDBS) of annihilation radiation and the studies revealed thermal diffusion of positrons into the interfacial regions within the core-shell structure and the "formation and pick-off annihilation of orthopositronium atoms". It is concluded that interface engineering is a strong means for manipulation of the magnetic, dielectric and magneto-electric properties in multiferroic heterostructures for high density electrical energy and magnetic data storage.

Chitosan ascorbate hydrogel improves water uptake capacity and cell adhesion of electrospun poly(epsilon-caprolactone) membranes.

The most important prerequisites for wound coverage matrices are biocompatibility, adequate porosity, degradability and exudate uptake capacity. A moderate hydrophilicity and exudate uptake capacity can often favour cell adhesion and wound healing potential, however, most of the synthetic polymers like polycaprolactone (PCL) are hydrophobic. Hydrogels based on natural polymers can improve the hydrophilicity and exudate uptake capacity of synthetic dressings and improve healing. In this work, we report the development of chitosan ascorbate-infiltrated electrospun PCL membranes. Our study demonstrated that chitosan ascorbate infiltration improves the hydrophilicity as well as water uptake capacity of the membranes and highly favoured the adhesion of human umbilical vein endothelial cells and human mesenchymal stem cells on the membranes.

In Situ Synthesis of Silver Nanospheres, Nanocubes, and Nanowires over Boron-Doped Graphene Sheets for Surface-Enhanced Raman Scattering Application and Enzyme-Free Detection of Hydrogen Peroxide.

An effective in situ synthesis strategy is demonstrated for the preparation of silver nanostructures (nanospheres (NSs), nanocubes (NCs), and nanowires (NWs)) on the surface of boron-doped graphene (BG). Further, these functional nanomaterials are employed for the surface-enhanced Raman scattering (SERS) and non-enzymatic electrochemical detection of H2O2. The results confirm the superior performance of BG-Ag nanostructures as SERS platform. Among various geometries of silver nanoparticles studied in this work, we find that the AgNCs over BG (BG-AgNC) present outstanding SERS performance for detecting 4-mercaptobenzoic acid, with a limit of detection of 1.0 × 10-13 M. Furthermore, BG-AgNC exhibits excellent capability to detect melamine as low as 1.0 × 10-9 M. Electrochemical results confirm that the BG-AgNW-based platform exhibits a superior biosensing performance toward H2O2 detection. The enhanced performance is due to the presence of graphene, which improves the conductivity and provides more active sites. The synthesis of doped graphene with metallic nanoparticles described in this work is expected to be a key strategy for the development of an efficient SERS and electrochemical sensor that offers simplicity, cost-effectiveness, long-term stability, and better reproducibility.

Low-Temperature Variation of Acoustic Velocity in PDMS for High-Frequency Applications.

Polydimethylsiloxane (PDMS) and other related silicon-based polymers are among the most widely employed elastomeric materials in microsystems, owing to their physical and chemical properties. Meanwhile, surface acoustic wave (SAW) and bulk acoustic wave (BAW) sensors and filters have been vastly explored for sensing and wireless applications. Many fields could benefit from the combined use of acoustic wave devices, and polydimethylsiloxane-based soft-substrates, microsystems, or packaging elements. The mechanical constants of PDMS strongly depend on frequency, similar to rubber materials. This brings to the exploration of the specific mechanical properties of PDMS encountered at high frequency, required for its exploitation in SAW or BAW devices. First, low-frequency mechanical behavior is confirmed from stress strain measurements, remaining useful for the exploitation of PDMS as a soft substrate or packaging material. The study, then, proposes a temperature-dependent, high-frequency mechanical study of PDMS based on Brillouin spectroscopy to determine the evolution of the longitudinal acoustic velocity in this material, which constitutes the main mechanical parameter for the design of acoustic wave devices. The PDMS glass transition is then retrieved by differential scanning calorimetry in order to confirm the observations made by Brillouin spectroscopy. This paper validates Brillouin spectroscopy as a very suitable characterization technique for the retrieval of longitudinal mechanical properties at low temperature, as a preliminary investigation for the design of acoustic wave devices coupled with soft materials.

Dopamine functionalization of BaTiO3: an effective strategy for the enhancement of electrical, magnetoelectric and thermal properties of BaTiO3-PVDF-TrFE nanocomposites.

Electro-active polymer-ceramic composite systems are emerging materials in the fields of nanoelectronic, microelectromechanical and macroelectronic device applications. Still more precise and concise research studies have yet to come in the areas of energy storage, harvesting, energy conversion, etc. In line with this, we have synthesized and analyzed PVDF-TrFE based nanocomposites of both functionalized and non-functionalized BaTiO3 (BTO). All the samples were prepared as free standing films by employing a solvent cast method. A systematic study of structural, morphological, thermal, dielectric, ferroelectric, piezoelectric and magnetoelectric (ME) properties has been carried out. It has been reported that the addition of BTO nanoparticles (with and without functionalization) into a polymer matrix substantially improved the properties of the nanocomposite. By performing the above mentioned characterization, it could be proved that dopamine functionalized BTO (DBTO) samples are better choices for the above mentioned applications including magnetoelectric applications, than the non-functionalized ones.

Surface Acoustic Wave Device with Reduced Insertion Loss by Electrospinning P(VDF-TrFE)/ZnO Nanocomposites.

Surface acoustic wave (SAW) devices have been utilized for the sensing of chemical and biological phenomena in microscale for the past few decades. In this study, SAW device was fabricated by electrospinning poly(vinylidenefluoride-co-trifluoroethylene) (P(VDF-TrFE)) incorporated with zinc oxide (ZnO) nanoparticles over the delay line area of the SAW device. The morphology, composition, and crystallinity of P(VDF-TrFE)/ZnO nanocomposites were investigated. After measurement of SAW frequency response, it was found that the insertion loss of the SAW devices incorporated with ZnO nanoparticles was much less than that of the neat polymer-deposited device. The fabricated device was expected to be used in acoustic biosensors to detect and quantify the cell proliferation in cell culture systems.

Dispersion of nanoparticles: from organic solvents to polymer solutions.

This work is devoted to a systematic study of nanoparticle dispersion by ultrasonication in different solutions: from organic solvents to polymer solutions. The cluster size of nanoparticles at different concentrations in both organic solvents and polymer solutions were directly characterized by Dynamic Light Scattering to study the effect of solid concentration, surfactant and polymer on the dispersion. It reveals that in stabilized suspensions, the smallest attainable size or aggregate size of nanoparticles is independent of solvent type and solid content over the tested range. Furthermore, nanoparticles in simple solvent and in polymer solutions had the similar evolution of cluster size and almost the same final size, which could be very helpful to optimize the dispersion of nanofillers in polymer solutions and nanocomposites. It is also shown that, with appropriate sonication amplitudes, the dispersion procedure developed for very dilute suspensions could be transferred to higher concentration suspensions or even to polymer suspensions.

Flexible over-moded resonators based on P(VDF-TrFE) thin films with very high temperature coefficient.

This work presents for the first time a flexible over-moded resonator (OMR) based on P(VDF-TrFE) thin films. The devices were manufactured on commercially available elastic substrate with inkjet-printed electrodes. The sensing copolymer films used in the devices were polarized by the corona method after electrode deposition. The main performance parameters of the component were then determined. The manufactured OMRs on P(VDF-TrFE) exhibited a linear variation of frequency versus temperature and a very large value of temperature coefficient of frequency (TCF ≫ 1600 ppm/°C). These properties suggest a great potential for using such components as low-cost and high-precision temperature sensors. The electromechanical coupling coefficient and the quality factor of the resonator were also characterized versus temperature.

Preparation and characterization of P(VDF-TrFE)/Al2O3 nanocomposite.

Hybrid nanocomposites based on crystalline nanoparticles dispersed in polymer matrix have been widely studied in the past few years because of the ability of these materials to combine the properties of organic polymer and inorganic nanoparticles. The aim of this work is to tune the mechanical properties of a piezoelectric polymer by adding nanoparticles to the matrix. In this paper, alumina nanoparticles were dispersed in the copolymer P(VDF-TrFE), which exhibits high piezoelectric coefficient after polarization under high electric field without needing stretching during the polarization process. Transmission electron microscopy and scanning electron microscopy demonstrate the high rate of welldispersed nanoparticles with 10% of alumina nanoparticles added to the matrix. Piezoelectric measurements indicate that P(VDF-TrFE) may be filled by up to 10 wt% of alumina while retaining its high piezoelectric properties and increasing its elastic constant by more than 20%, measured by Brillouin spectroscopy. This work opens a wide range of applications using nanoparticles with nonlinear optical, pyroelectric, magnetic, or ferroelectric properties.

Effect of ultrasonication and dispersion stability on the cluster size of alumina nanoscale particles in aqueous solutions.

This study deals with the deagglomeration of nanoparticles in low concentration suspensions in water, protic polar solvent for polymers such as poly(vinyl alcohol) (PVA). The influence of the main parameters of ultrasonication such as time, power and irradiation modes (continuous, pulsed) on the cluster size of aluminium oxide nanoparticles 1 mg/ml in aqueous solutions was investigated. Power-law dependence of size reduction on ultrasonic time was observed. The study indicated an optimum power input, i.e. at higher vibration amplitude the break up of nanoparticle clusters was no better and there was a risk of reagglomeration occurring during a long ultrasonication. Under optimal conditions, continuous and pulsed irradiations showed almost the same efficiency of deagglomeration over a given time. This result provides alternative operating conditions for attaining the smallest size of the alumina aggregates in suspension. The influence of stabilization on the cluster size was also studied. Alumina nanoparticles were stabilized by electrostatic forces against reagglomeration without the need for dispersants, and the enhancement of dispersion stability using electrostatic, steric effects had no significant effect on the aggregate size. On the contrary, the adsorption of high molecular weight polyelectrolytes onto the particle surface could lead to reagglomeration due to material bridges between particle surfaces and even flocculation.

New synthesis of nanosized niobium oxides and lithium niobate particles and their characterization by XPS analysis.

This work presents a new synthesis of nano-sized lithium niobate particles by a low temperature three steps procedure. The complete protocol implies a LiH induced reduction of NbCl5 followed by in situ spontaneous oxidation into low valence niobium nano-oxides. These niobium oxides are exposed to air atmosphere leading to pure Nb2O5 formation. Finally, the stable Nb2O5 is converted into lithium niobate LiNbO3 nanoparticles during the controlled hydrolysis of the LiH excess. The nano-sized lithium niobate particles as well as their formation processes were characterized using X-ray photoelectron spectroscopy.

Temperature study of potassium niobate (KNbO(3)) elastic constants by Brillouin spectroscopy.

This study deals with using Brillouin spectroscopy to determine the temperature variation of potassium niobate elastic constants. Two different samples have been used (Y- and Z-cut), and all the measurements were done in the temperature range between 300 K and 420 K. The calculations concern only the first-order coefficients. The acoustic velocity is then determined for each sample in 3 directions of propagation. Results are given for C( 22), C( 55), and C( 66) elastic constants and accuracy problems are discussed.